Khadivparsi, Parissa, Rafiee-Tehrani, Morteza, Dorkoosh, Farid, Babaee Darabad, Jabber, Azizpour, Hedayat, Rezamandi, Nariman, Larki, Nadia. (1402). The Influence of Polymer Type and Concentration on the Metoprolol Mass Transfer in Extended-Release Tablet of Metoprolol Succinate. , 57(1), 97-109. doi: 10.22059/jchpe.2023.351673.1418
Parissa Khadivparsi; Morteza Rafiee-Tehrani; Farid Dorkoosh; Jabber Babaee Darabad; Hedayat Azizpour; Nariman Rezamandi; Nadia Larki. "The Influence of Polymer Type and Concentration on the Metoprolol Mass Transfer in Extended-Release Tablet of Metoprolol Succinate". , 57, 1, 1402, 97-109. doi: 10.22059/jchpe.2023.351673.1418
Khadivparsi, Parissa, Rafiee-Tehrani, Morteza, Dorkoosh, Farid, Babaee Darabad, Jabber, Azizpour, Hedayat, Rezamandi, Nariman, Larki, Nadia. (1402). 'The Influence of Polymer Type and Concentration on the Metoprolol Mass Transfer in Extended-Release Tablet of Metoprolol Succinate', , 57(1), pp. 97-109. doi: 10.22059/jchpe.2023.351673.1418
Khadivparsi, Parissa, Rafiee-Tehrani, Morteza, Dorkoosh, Farid, Babaee Darabad, Jabber, Azizpour, Hedayat, Rezamandi, Nariman, Larki, Nadia. The Influence of Polymer Type and Concentration on the Metoprolol Mass Transfer in Extended-Release Tablet of Metoprolol Succinate. , 1402; 57(1): 97-109. doi: 10.22059/jchpe.2023.351673.1418

The Influence of Polymer Type and Concentration on the Metoprolol Mass Transfer in Extended-Release Tablet of Metoprolol Succinate

Journal of Chemical and Petroleum Engineering
دوره 57، شماره 1، شهریور 2023، صفحه 97-109    اصل مقاله (771.12 K)
نوع مقاله: Research Paper
شناسه دیجیتال (DOI): 10.22059/jchpe.2023.351673.1418
نویسندگان
Parissa Khadivparsi* 1؛ Morteza Rafiee-Tehrani2؛ Farid Dorkoosh3؛ Jabber Babaee Darabad4؛ Hedayat Azizpour1؛ Nariman Rezamandi5؛ Nadia Larki1
1School of Chemical Engineering, College of Engineering, University of Tehran, Tehran, Iran
2Department of Pharmaceutics, Faculty of Pharmacy, Tehran University of Medical Sciences, Tehran, Iran
3Medical Biomaterial Research Center, Tehran University of Medical Sciences, Tehran, Iran
4Shimi Pajohan Sabze Nikan, Tehran, Iran
5Department of Civil, Chemical, Environmental, and Material Engineering (DICAM), Alma Mater Studiorum – University of Bologna, Bologna, Italy
چکیده
Metoprolol has been widely used for controlling high blood pressure, preventing myocardial reinfarction, setting rate changes, setting heart rhythm, treatment of chronic angina and preventing excessive bleeding during surgery. The purpose of this research is formulation and manufacture of extended release tablets of metoprolol succinate that conform to all the in vitro physicochemical US Pharmacopoeia national formulary (USP32). For preparing the tablets, the hydrophilic HPMC(K100M) polymer was used in direct compression method. Release of metoprolol in phosphate buffer having pH=6.8 (USP32) was measured by HPLC. Also, using experimental correlation of diffusivity in buffer medium and Gurney-Lurie charts during tablet enlargement with time, diffusion coefficients of drug and partition coefficients were obtained at different time steps. The rate of drug release depends on the type, viscosity and polymer concentration. Drug release results over 20 hours for polymers of HPMC(K100M), HPMC(K4M), HPMC(K15M), polyethylene oxide, ethyl cellulose, Eudragit (RL100) were investigated and compared. The results demonstrated that HPMC(K100M) met the standards of USP32 very well and was superior over the other polymers tested.
کلیدواژه‌ها
Metoprolol؛ Extended-Release Tablets؛ HPMC Polymer؛ Mass Transfer
مراجع
آمار
تعداد مشاهده مقاله: 722
تعداد دریافت فایل اصل مقاله: 1,331