پیوندهای مفید
اخبار و اعلانات
آمار
| تعداد نشریات | 127 |
| تعداد شمارهها | 7,196 |
| تعداد مقالات | 77,227 |
| تعداد مشاهده مقاله | 157,208,897 |
| تعداد دریافت فایل اصل مقاله | 118,400,383 |
The effect of SiC polytype on the solar cell characteristics: a simulation study | ||
| Journal of Solar Energy Research | ||
| دوره 11، شماره 2، تیر 2026، صفحه 2977-2991 اصل مقاله (1.11 M) | ||
| نوع مقاله: Research Article | ||
| شناسه دیجیتال (DOI): 10.22059/jser.2026.410248.1710 | ||
| نویسندگان | ||
| Rand Kareem Husein؛ Burak Yahya Kadem* | ||
| College of Science, Al-Karkh University of Science, Baghdad, Iraq | ||
| چکیده | ||
| Solar cells based on P3HT, SiC, and ZnS were examined via SCAPS-1D to estimate the impact of different silicon carbide (SiC) polytypes as an interlayer, including 3C-SiC, 4H-SiC, and 6H-SiC, on device performance. Different analyses were conducted to explain charge transport and interfacial behavior, including current-voltage (J-V), external quantum efficiency (EQE), Mott-Schottky, and recombination rate. Among the studied solar cells, using 3C-SiC interlayer exhibited the highest performance and a clear reduction in interfacial recombination, achieving a short-circuit current density (JSC) of 15.18 mA/cm², a fill factor (FF) of 81.6%, and a power conversion efficiency (PCE) of 19.2%. Conversely, 6H-SiC has resulted in moderate improvements, whereas 4H-SiC led to a decline in performance. Further optimization of the 3C-SiC interlayer thickness, particularly in the 70-100 nm range, proved critical in balancing band bending, interfacial passivation, and carrier extraction, factors that collectively contributed to maximizing both FF and PCE. Further examinations were carried out to study the effects of trap density, effective density of states, series and shunt resistances, and illumination conditions to evaluate their significance on the solar cell performance. These findings demonstrate that appropriate SiC polytype with careful interface engineering, plays an essential role in enhancing the efficiency of solar cells. | ||
| کلیدواژهها | ||
| Hybrid solar cell؛ 3C-SiC؛ Energy band alignment Interfacial layer؛ SiC polytypes؛ Organic-inorganic heterojunction | ||
| مراجع | ||
|
[1] Feng, Z. C., Lin, H. H., Xin, B., Tsai, S. J., Saravade, V., Yiin, J., Klein, B., & Ferguson, I. T. (2023). Structural characteristics of 3C-SiC thin films grown on Si-face and C-face 4H-SiC substrates by high temperature chemical vapor deposition. Vacuum, 207, 111643. https://doi.org/10.1016/j.vacuum.2022.111643
[2] Bhatnagar, M., & Baliga, B. J. (1993). Comparison of 6H-SiC, 3C-SiC, and Si for power devices. IEEE Transactions on Electron Devices, 40(3), 645-655. https://doi.org/10.1109/16.199372
[3] Harris, C. I., Savage, S., Konstantinov, A., Bakowski, M., & Ericsson, P. (2001). Progress towards SiC products. Applied Surface Science, 184(1-4), 393-398. https://doi.org/10.1016/S0169-4332(01)00525-6
[4] Schöner, A., Krieger, M., Pensl, G., Abe, M., & Nagasawa, H. (2006). Fabrication and characterization of 3C-SiC-based MOSFETs. Chemical Vapor Deposition, 12(8-9), 523-530. https://doi.org/10.1002/cvde.200606467
[5] Ferry, D. K. (1975). High-field transport in wide-band-gap semiconductors. Physical Review B, 12(6), 2361. https://doi.org/10.1103/PhysRevB.12.2361
[6] Huang, J. J., Militzer, C., Wijayawardhana, C., Forsberg, U., Ojamae, L., & Pedersen, H. (2022). Controlled CVD growth of highly ⟨111⟩-oriented 3C-SiC. The Journal of Physical Chemistry C, 126(23), 9918-9925.https://doi.org/10.1021/acs.jpcc.2c01171
[7] Syväjärvi, M., Ma, Q., Jokubavicius, V., Galeckas, A., Sun, J., Liu, X., et al. (2016). Cubic silicon carbide as a potential photovoltaic material. Solar Energy Materials and Solar Cells, 145, 104-108. https://doi.org/10.1016/j.solmat.2015.08.029
[8] Yang, N., Zhuang, H., Hoffmann, R., Smirnov, W., Hees, J., Jiang, X., & Nebel, C. E. (2011). Nanocrystalline 3C-SiC electrode for biosensing applications. Analytical Chemistry, 83(15), 5827-5830. https://doi.org/10.1021/ac201315q
[9] Kato, M., Yasuda, T., Miyake, K., Ichimura, M., & Hatayama, T. (2014). Epitaxial p-type SiC as a self-driven photocathode for water splitting. International Journal of Hydrogen Energy, 39(10), 4845-4849. https://doi.org/10.1016/j.ijhydene.2014.01.049
[10] Yazdi, G. R., Iakimov, T., & Yakimova, R. (2016). Epitaxial graphene on SiC: A review of growth and characterization. Crystals, 6(5), 53. https://doi.org/10.3390/cryst6050053
[11] Yazdi, G. R., Vasiliauskas, R., Iakimov, T., Zakharov, A., Syväjärvi, M., & Yakimova, R. (2013). Growth of large area monolayer graphene on 3C-SiC and a comparison with other SiC polytypes. Carbon, 57, 477-484. https://doi.org/10.1016/j.carbon.2013.02.022
[12] Backes, C., Abdelkader, A. M., Alonso, C., et al. (2020). Production and processing of graphene and related materials. 2D Materials, 7(2), 022001. https://doi.org/10.1088/2053-1583/ab1e0a
[13] Shi, Y. (2019). Growth of 3C-SiC and graphene for solar water-splitting application. Linköping University Dissertation. https://doi.org/10.3384/diss.diva-159100
[14] Janz, S., Reber, S., Lutz, F., & Schetter, C. (2006). Conductive SiC as an intermediate layer for CSITF solar cells. Thin Solid Films, 511, 271-274. https://doi.org/10.1016/j.tsf.2005.11.102
[15] Sameera, J. N., Islam, M. A., Islam, S., Hossain, T., Sobayel, M. K., Akhtaruzzaman, M., et al. (2022). Cubic silicon carbide (3C-SiC) as a buffer layer for high efficiency CdTe solar cell. Optical Materials, 123, 111911. https://doi.org/10.1016/j.optmat.2021.111911
[16] Zouache, R., Saidani, O., Yousfi, A., Alsubaie, A. S., Soulef, B. A., Feriel, L., & Islam, R. (2025). Numerical investigation of enhanced efficiency in CIGS solar cells with 3C-SiC and PEDOT:PSS integration. Periodica Polytechnica Chemical Engineering, 69(1), 26-34. https://doi.org/10.3311/PPch.38770
[17] Wang, L., Yang, F., Pei, Y., Yang, X., & Lorenz, L. (2026). Packaging and integration of silicon carbide power devices. Nature Reviews Electrical Engineering. https://doi.org/10.1038/s44287-026-00263-0
[18] Hasan, A. A., Zuhdi, A. M., Al-Ghaili, A. M., Al-Shetwi, A. Q., Islam, M. A., Sankar, K. P., & Gunasekaran, S. S. (2025). A review on silicon photovoltaic module degradations and recent identification techniques. Solar Energy, 288, 113288. https://doi.org/10.1016/j.solener.2025.113288
[19] Kadem, B. Y., & Abbas, E. M. (2024). Optimization of several parameters towards 30% efficiency perovskite solar cell using SCAPS-1D software. Iraqi Journal of Physics, 22(4), 117-129.
[20] Yassine, B., Tahar, B., & Fathi, G. (2022). Modeling and simulation of CZTS based solar cells using SCAPS-1D. Chalcogenide Letters, 19(8), 503-511. https://doi.org/10.15251/CL.2022.198.503
[21] Mekaret, F., et al. (2024). A comparative study of Schottky barrier heights and charge transport mechanisms in SiC polytypes. AIP Advances, 14(11). https://doi.org/10.1063/5.0240123
[22] Kadem, B., Hassan, A., & Cranton, W. (2016). Efficient P3HT:PCBM solar cells. Journal of Materials Science: Materials in Electronics, 27(7), 7038-7048. https://doi.org/10.1007/s10854-016-4661-8
[23] Sofia, J. R., & Wilson, K. J. (2023). Optimization of Jsc in DSSCs. Optik, 290, 171287. https://doi.org/10.1016/j.ijleo.2023.171287
[24] Kadem, B. Y. (2025). PEDOT:PSS thin films for solar cells. Nanomaterials and Energy, 14(2), 1-10. https://doi.org/10.1680/jnaen.24.00014
[25] Brudnyi, V. N., & Kosobutsky, A. V. (2017). Electronic properties of SiC polytypes. Superlattices and Microstructures, 111, 499-505. https://doi.org/10.1016/j.spmi.2017.07.003
[26] Tress, W., et al. (2015). Radiative and non-radiative recombination in perovskites. Advanced Energy Materials, 5(3), 1400812. https://doi.org/10.1002/aenm.201400812
[27] Sozzi, G., et al. (2016). CIGS CV characteristics analysis. IEEE PVSC. https://doi.org/10.1109/PVSC.2016.7750043
[28] Zerfaoui, H., Dib, D., & Kadem, B. (2019). SiC solar cell light intensity effects. Silicon, 11(4), 1917-1923. https://doi.org/10.1007/s12633-018-0011-1
[29] McIntosh, K. R., et al. (2009). Luminescent down-shifting in Si solar cells. Progress in Photovoltaics, 17(3), 191-197. https://doi.org/10.1002/pip.867
[30] Jian, J., et al. (2019). NiO/3C-SiC photoanode. Journal of Materials Chemistry A, 7(9), 4721-4728. https://doi.org/10.1039/C9TA00020H
[31] Morab, S., Sundaram, M. M., & Pivrikas, A. (2023). Review on charge carrier transport in inorganic and organic semiconductors. Coatings, 13(9), 1657. https://doi.org/10.3390/coatings13091657
[32] Al-Hashimi, M. K., Kadem, B. Y., & Hassan, A. K. (2018). Rutile TiO₂ films as electron transport layer in inverted organic solar cell. Journal of Materials Science: Materials in Electronics, 29(9), 7152-7160. https://doi.org/10.1007/s10854-018-8703-2
[33] Liu, X., Guo, J., Hao, R., Zhao, Q., Chang, F., Wang, L., Liu, B., Li, Y., & Gu, K. (2019). Cliff-like conduction band offset at CdS/Cu₂ZnSnS₄ heterojunction prepared by sputtering CuSn alloy target. Solar Energy, 183, 285-292. https://doi.org/10.1016/j.solener.2019.03.033
[34] Wang, A., He, M., Green, M. A., Sun, K., & Hao, X. (2023). A critical review on the progress of kesterite solar cells. Advanced Energy Materials, 13(2), 2203046. https://doi.org/10.1002/aenm.202203046
[35] Baig, F., Khattak, Y. H., Shuja, A., Riaz, K., & Soucase, B. M. (2020). Performance investigation of Sb₂Se₃ solar cells in SCAPS-1D. Current Applied Physics, 20(8), 973-981. https://doi.org/10.1016/j.cap.2020.06.005
[36] Ghorbani, E. (2020). On efficiency of earth-abundant chalcogenide photovoltaic materials. Journal of Physics: Energy, 2(2), 025002. https://doi.org/10.1088/2515-7655/ab6942
[37] Vollbrecht, J., Tokmoldin, N., Sun, B., et al. (2023). Effective mobility in organic solar cells. Energy Advances, 2(9), 1390-1398. https://doi.org/10.1039/D3YA00125C
[38] Kasap, S. O. (2006). Electronic materials and devices (pp. 336-339). McGraw-Hill.
[39] Betti, M. G., Corradini, V., Bertoni, G., Casarini, P., Mariani, C., & Abramo, A. (2001). Density of states of a two-dimensional electron gas. Physical Review B, 63(15), 155315. https://doi.org/10.1103/PhysRevB.63.155315
[40] Xia, J., Sohail, M., & Nazeeruddin, M. K. (2023). Interface engineering in perovskite solar cells. Advanced Materials, 35(31), 2211324. https://doi.org/10.1002/adma.202211324
[41] Davydov, S. Y. (2007). Electron affinity of silicon carbide polytypes. Semiconductors, 41(6), 696-698. https://doi.org/10.1134/S1063782607060152
[42] Kephart, J. M., McCamy, J. W., Ma, Z., et al. (2016). Band alignment in CdTe solar cells. Solar Energy Materials and Solar Cells, 157, 266-275. https://doi.org/10.1016/j.solmat.2016.05.050
[43] Yang, Q., Bittkau, K., Eberst, A., Rau, U., & Ding, K. (2024). Interface recombination in silicon solar cells. Solar Energy Materials and Solar Cells, 273, 112953. https://doi.org/10.1016/j.solmat.2024.112953
[44] Haq, A. U., Buerkle, M., Askari, S., et al. (2020). Energy-level alignment in silicon carbide nanocrystals. The Journal of Physical Chemistry Letters, 11(5), 1721-1728. https://doi.org/10.1021/acs.jpclett.9b03828
[45] Bagade, S. S., Barik, S. B., Malik, M. M., & Patel, P. K. (2023). Band alignment in perovskite solar cells. Materials Today: Proceedings. https://doi.org/10.1016/j.matpr.2023.02.117
[46] Lopez-Varo, P., Jiménez-Tejada, J. A., García-Rosell, M., et al. (2018). Device physics of hybrid perovskite solar cells. Advanced Energy Materials, 8(14), 1702772. https://doi.org/10.1002/aenm.201702772
[47] Ahmed, A., Riaz, K., Mehmood, H., et al. (2020). ETL optimization in perovskite solar cells. Optical Materials, 105, 109897. https://doi.org/10.1016/j.optmat.2020.109897
[48] Ding, C., Zhang, Y., Liu, F., et al. (2018). Conduction band offset in perovskite solar cells. Nano Energy, 53, 17-26. https://doi.org/10.1016/j.nanoen.2018.08.031
[49] Bivour, M., Schröer, S., & Hermle, M. (2013). TCO/a-Si:H contact properties. Energy Procedia, 38, 658-669. https://doi.org/10.1016/j.egypro.2013.07.330
[50] Kesavan, A. V., Rao, A. D., & Ramamurthy, P. C. (2017). Interface morphology in organic photovoltaics. ACS Applied Materials & Interfaces, 9(34), 28774-28784. https://doi.org/10.1021/acsami.7b03953
[51] Armstrong, C. L., Price, M. B., Munoz-Rojas, D., et al. (2015). Inorganic interlayers in hybrid solar cells. ACS Nano, 9(12), 11863-11871. https://doi.org/10.1021/acsnano.5b05934
[52] Kim, H., Lee, K. S., Paik, M. J., et al. (2022). PMMA interlayer in perovskite solar cells. Advanced Functional Materials, 32(13), 2110473. https://doi.org/10.1002/adfm.202110473
[53] Sherkar, T. S., Momblona, C., Gil-Escrig, L., et al. (2017). Recombination in perovskite solar cells. ACS Energy Letters, 2(5), 1214-1222. https://doi.org/10.1021/acsenergylett.7b00236
[54] Singh, P., & Ravindra, N. M. (2012). Temperature dependence of solar cell performance. Solar Energy Materials and Solar Cells, 101, 36-45. https://doi.org/10.1016/j.solmat.2012.02.019
[55] Shaker, L. M., Al-Amiery, A. A., Hanoon, M. M., et al. (2024). Thermal effects on solar cells. Sustainable Energy Research, 11(1), 6. https://doi.org/10.1186/s40807-024-00100-8
[56] Mundhaas, N., Yu, Z. J., Bush, K. A., et al. (2019). Series resistance in perovskite solar cells. Solar RRL, 3(4), 1800378. https://doi.org/10.1002/solr.201800378
[57] Park, Y., Noh, S., Lee, D., Kim, J. Y., & Lee, C. (2011). Temperature dependence in polymer solar cells. Journal of the Korean Physical Society, 59(2), 362-366. https://doi.org/10.3938/jkps.59.362
[58] Scheunemann, D., Wilken, S., Parisi, J., & Borchert, H. (2016). Charge carrier loss in CuInS₂/ZnO solar cells. Physical Chemistry Chemical Physics, 18(24), 16258-16265. https://doi.org/10.1039/C6CP01015F
[59] Kumar, A., & Ranjan, P. (2021). VOC characterization in thin-film solar cells. Solar Energy, 220, 35-42. https://doi.org/10.1016/j.solener.2021.03.017
[60] Sobayel, M. K., Chowdhury, M. S., Hossain, T., et al. (2021). Efficiency enhancement of CIGS solar cells using 3C-SiC buffer layer. Solar Energy, 224, 271-278. https://doi.org/10.1016/j.solener.2021.05.093 | ||
|
آمار تعداد مشاهده مقاله: 322 تعداد دریافت فایل اصل مقاله: 108 |
||
سامانه مدیریت نشریات علمی. قدرت گرفته از سیناوب