|تعداد مشاهده مقاله||108,117,806|
|تعداد دریافت فایل اصل مقاله||84,520,055|
Geotechnical Investigation of Tailings Disposal Site for Tailings Storage of zinc Processing Factory
|دوره 8، شماره 1، فروردین 2022، صفحه 1-14 اصل مقاله (1.01 M)|
|نوع مقاله: Original Research Paper|
|شناسه دیجیتال (DOI): 10.22059/poll.2021.320134.1029|
|College of Environment, P.O.Box 31746-118, Karaj, Iran Research Group of Environmental Engineering, Research Center for Environment and Sustainable Development, P.O.Box 463913116, Teheran, Iran|
|The present study aims at determining the geotechnical properties of the tailings and the natural bed at Iran Mineral Processing Company, Sites 1 and 5. It qualitatively studies the subsurface layers of the company’s tailings storage site. After drilling different boreholes and conducting in-situ tests, it has made laboratory analyses in the form of field exploration to determine the geotechnical parameters of the extracted samples. Results from the analyses show the permeability coefficient of the subsurface layer of Site No. 1 and 5 to be very small, in the range of 10-7 cm/sec. Considering the conformity of permeability coefficient, percentage of fine grains (98% to 99%), plasticity index (28.5-29.5), and clay content of different layers of Sites 1 and 5 (68%-80%), based on the compacted clay liner criteria, it can be concluded that by nature, the subsurface layers of the mentioned sites are sealed with no need for any compacted clay liner. The tailings for storage Site 5 are fine-grained (80-88<75mm), basically in ML range according to USCS system, with a permeability coefficient of about 10-6 cm/sec. Therefore, the tailings themselves act as a relatively primary sealing layer against the infiltration of hazardous leachates into the natural bed. The method, used in the process of site selection of tailings storage facilities (TSF), can cut the construction time as well as the expenditures, thus reducing the production costs in the long run.|
|Tailings Properties؛ Permeability؛ Filter Cake؛ Site Selection|
AASHTO (2002), Standard Specifications for Highway Bridges, 17th ed. American Association of State Highway and Transportation Officials (AASHTO), Washington, D.C.
Adajar, M.A.Q. and Zarco, M.A.H. (2014). An Empirical Model for Predicting Hydraulic Conductivity of Mine Tailings. Int. J. Geomate, 7(2), 1054-1061.
Al-Jabri, K.S., Taha, R.A., Al-Hashmi, A. and Al-Harthy, A.S. (2006). Eﬀect of copper slag and cement by-pass dust addition on mechanical properties of concrete. Constr. Build. Mater. 20, 322–331, doi:10.1016/j.conbuildmat.2005.01.020.
ASTM D1556/D1556M-15e1 (2015), Standard Test Method for Density and Unit Weight of Soil in Place by Sand-Cone Method, ASTM International, West Conshohocken, PA, DOI: 10.1520/D1556_D1556M-15E01.
ASTM D2216-19 (2019), Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass, ASTM International, West Conshohocken, PA, DOI: 10.1520/D2216-19.
ASTM D854-14 (2014), Standard Test Methods for Specific Gravity of Soil Solids by Water Pycnometer, ASTM International, West Conshohocken, PA, DOI: 10.1520/D0854-14.
ASTM D422-63-e2 (2007), Standard Test Method for Particle-Size Analysis of Soils (Withdrawn 2016), ASTM International, West Conshohocken, PA, DOI: 10.1520/D0422-63R07E02.
ASTM D4318-17e1 (2017), Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils, ASTM International, West Conshohocken, PA, DOI: 10.1520/D4318-17E01.
ASTM D2937-17e2 (2017), Standard Test Method for Density of Soil in Place by the Drive-Cylinder Method, ASTM International, West Conshohocken, PA, DOI: 10.1520/D2937-17E02.
ASTM D2487-17e1 (2017), Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System), ASTM International, West Conshohocken, PA, DOI: 10.1520/D2487-17E01.
The Organizing Committee of the 12th International Conference on Tailings and Mine Waste (2009), Tailings and Mine Waste ’08 (Athanassopoulos C., Kohlman A., Henderson M. and Kaul J., Evaluation of geomembrane puncture potential and hydraulic performance in mining applications (189-198). London: Taylor & Francis Group.)
Aubertin, M., Bussiere, B. and Chapuis, R. (1996). Hydraulic Conductivity of Homogenized Tailings from Hard Rock Mines. Can. Geotech. J., Vol. 33(3), 470 –482. https://doi.org/10.1139/t96-068
Aubertin, M., Ricard, J.F. and Chapuis, R.P. (1998). A predictive model for the water retention curve: application to tailings from hard-rock mines, Can. Geotech. J., 35(1): 55-69, https://doi.org/10.1139/t97-080.
Blas, J. and Bream, R. (2008). Chinese agree 96% jump in ore prices. Financial Times. (London)
Brindha, D. and Nagan, S. (2011). Durability studies on copper slag admixed concrete. Asian J. Civil Eng. (Building and Housing). 12(5), 563–578. Google Scholar.
Carmo, F. F., Lanchotti, A.O. and Kamino, L.H.Y. (2020). Mining Waste Challenges: Environmental Risks of Gigatons of Mud, Dust and Sediment in Megadiverse Regions in Brazil, Sustainability, 12(20), 8466; https://doi.org/10.3390/su12208466
Chen, A., Zhao Z.W., Jia, X., Long, S., Huo, G. and Chen, X. (2009). Alkaline leaching Zn and its concomitant metals from refractory hemimorphite zinc oxide ore. Hydrometallurgy. 97(3-4):228–232. https://doi.org/10.1016/j.hydromet.2009.01.005
Dolatabad, Y. A. and Tarqi, M. N. (2017). Applying Solid Residues of Copper Slag in Kerman Sarcheshme of Iran as Sand Replacement for Self-Compacting Concrete. Environmental Energy and Economic Research 1(3): 333-346, DOI 10.22097/eeer.2018.105539.1015.
Esmaeili, J. and Aslani, H. (2019). Use of copper mine tailing in concrete: strength characteristics and durability performance, Journal of Material Cycles and Waste Management 21(8), DOI: 10.1007/s10163-019-00831-7.
Blight, G. E. (2010). Geotechnical Engineering for Mine Waste Storage Facilities, (London: CRC Press, Taylor & Francis.)
Giurco, D. (2010). Peak Minerals in Australia: A Review of Changing Impacts and Beneﬁts. Institute for Sustainable Futures, University of Technology, Sydney; Department of Civil Engineering, Monash University.
Koohestani, H., Khatami, E. S. and Babaei, K. (2019). Comparative investigation of leaching of zinc from wastes of the zinc alloy production process. Miner. Process. Extr. Metall., DOI: 10.1080/25726641.2019.1660506
He, S., Wang, J. and Yan, J. (2010). Pressure leaching of high silica Pb–Zn oxide ore in sulfuric acid medium. Hydrometallurgy. 104(2):235–240. https://doi.org/10.1016/j.hydromet.2010.06.011
Hu, L., Wu, H., Zhang, L., Zhang, P. and Wen, Q. (2017). Geotechnical Properties of Mine Tailings, J. Mater. Civ. Eng., 29(2).
Hurşit, M., Laçin, O. and Saraç, H. (2009). Dissolution kinetics of smithsonite ore as an alternative zinc source with an organic leach reagent. J Taiwan Inst Chem Eng. 40(1), 6–12. DOI: 10.1016/j.jtice.2008.07.003
Instruction for Laboratory and field Permeability testing, No. 188 (2000). Plan and Budget Organization, Office of deputy of Technical Affaires, Bureau of Technical Affaires and Standards.
Kossoff, D., Dubbin, W.E., Alfredsson, M., Edwards, S.J., Macklin, M.G. and Hudson-Edwards, K.A. (2014). Mine tailings dams: Characteristics, failure, environmental impacts, and remediation. Appl. Geochem., 51, 229–245. http://dx.doi.org/10.1016/j.apgeochem.2014.09.010
Kumar, K. and Naik, R. (2015). Experimental Study on Utilization of Industrial Wastes (Red mud and Copper slag) in Mortar and Concrete, International Journal of Civil and Structural Engineering Research, 3(1), 228-233, Available at: www.researchpublish.com
Li, C-x., Xu, H-s., Deng, Z-g., Li, X-b., Li, M-t. and Wei, C. (2010). Pressure leaching of zinc silicate ore in sulfuric acid medium. Trans Nonferrous Met Soc China., 20(5), 918–923. https://doi.org/10.1016/S1003-6326(09)60236-3
Lottermoser, B. (2007). Mine Wastes: Characterization, Treatment and Environmental Impacts. Springer, Berlin, Heidelberg, New York. DOI 10.1007/978-3-642-12419-8_1,
Marion, C., Williams, H., Langlois, R., Kökkılıç, O., Coelho, F., Awais, M., Rowson, N.A. and Waters, K.E. (2017). The potential for dense medium separation of mineral ﬁnes using a laboratory Falcon Concentrator. Miner. Eng. 105, 7–9. https://doi.org/10.1016/j.mineng.2016.12.008
Meng, C. Song, N.P., Yue, J.M., Xie, L., Zhong, Y.X. and Du, L.T. (2020). Screening of hyperaccumulator plants tolerant to drought and salinity and its medicinal value evaluation for ecological reconstruction of copper silver tailings in Northwest China, Pollution, 7(1), 87-100, DOI: 10.22059/poll.2020.307386.862.
Mohammed, T.U., Rahman, M. N., Mahmood, A.H. and Hasan, M. T. (2016, August). Utilization of Steel Slag in Concrete as Coarse Aggregate, (Paper presented at the 4th International Conference on Sustainability of Construction Materials and Technologies (SCMT4), At Las Vegas). DOI: 10.13140/RG.2.1.3804.4404
Onuaguluchi, O. and Eren, Ö. (2012). Copper tailings as a potential additive in concrete: Consistency, strength and toxic metal immobilization properties, Indian J. Eng. Mater. Sci., 19(2), 79-86. http://hdl.handle.net/123456789/14144
Padmapriya, R., Bupesh, V. K., Raja, V., Kumar, G. and Baalamurugan, J. (2015). Study on replacement of coarse aggregate by steel slag and fine aggregate by manufacturing sand in concrete, International Journal of ChemTech Research. 8(4), 1721-1729.
Duan, P., Shui, Z., Chen, W. and Shen, C. (2013). Enhancing microstructure and durability of concrete from ground granulated blast furnace slag and metakaolin as cement replacement materials, J. Mater. Res. Technol., 2(1), 52-59. https://doi.org/10.1016/j.jmrt.2013.03.010
Pujar, S. M. And Prakash, K. B. (2014). Effect of replacement of cement by red mud on the properties of concrete. Int. J. Sci. Eng. Res., 5(9), 805-814.
Qiu, Y. and Sego, D.C. (2001). Laboratory Properties of Mine Tailings. Can. Geotech. J. 38: 183-190.
Quille, M. E. and Kelly, O. (2010, June). Geotechnical Properties of Zinc/Lead Mine Tailings from Tara Mines, Ireland, (Paer presented at the GeoShanghai International Conference Shanghai), https://doi.org/10.1061/41105(378)16.
Raj, S., Rai, A.K. and Havanagi, V.G. (2018). Suitability of stabilized copper slag and fly ash mix for road construction, World Journal of Engineering. 15(3) 336–344, DOI10.1108/WJE-08-2017-0220.
Ribeiro, D.V., Labrincha, J.A. and Morelli, M.R. (2011). Potential Use of Natural Red Mud as Pozzolan for Portland Cement. Materials Research 14 (1), 60-66, DOI: 10.1590/S1516-14392011005000001
Ruan, Z., Li, M., Gao, K., Zhang, D., Huang, L., Xu, W. and Liu, X. (2019). Eﬀect of Particle Size Reﬁnement on the Leaching Behavior of Mixed Rare-Earth Concentrate Using Hydrochloric Acid. ACS Omega, 4, 9813−9822. DOI: 10.1021/acsomega.9b01141.
Saafan, M.A.,·Etman, Z.A. and·lakany, D.M., 2019. Microstructure and Durability of Ground Granulated Blast Furnace Slag Cement Mortars, Iranian Journal of Science and Technology, Transactions of Civil Engineering https://doi.org/10.1007/s40996-020-00533-3.
Sarsby, R.W. (2000). Environmental Geotechnics. Thomas Telford, London.
Sarsby, R. W. (2013). Environmental Geotechnics, 2nd Edition, Published by ICE Publishing.
Santos, F.M.F., Pina, P.S., Porcaro, R., Oliveira, V.A., Silva, C.A., Leão,V.A. (2010). The kinetics of zinc silicate leaching in sodium hydroxide. Hydrometallurgy. 102(1):43–49. https://doi.org/10.1016/j.hydromet.2010.01.010
Sharmila, P. and Dhinakaran, G. (2016). Compressive strength, porosity and sorptivity of ultra ﬁne slag based high strength concrete, Constr. Build. Mater. 120, 48–53, http://dx.doi.org/10.1016/j.conbuildmat.2016.05.090
Shirdam, R., Amini, M., Bakhshi, N. (2014). “The Application of Sarcheshmeh and Khatounabad Copper Slag in Road Base and Subbase” 7th National Conference & Exhibition on Environmental Engineering, University of Tehran, Tehran, Iran. https://www.civilica.com/Paper-CEE07-CEE07_088.html
Shirdam, R., Amini, M. and Bakhshi, N. (2019a). Investigating the effects of copper slag and silica fume on durability, strength, and workability of concrete, Int. J. Environ. Res, 13(6), https://doi.org/10.1007/s41742-019-00215-7
Shirdam, R., Nourigohar, A. and Mohamadi, S. (2019b). Stabilization of Filter Cake and its Leaching Behaviour: A Case Study with Cementitious and Soluble Phosphate Additives, Pollution, 5(3), 525-536. DOI: 10.22059/poll.2019.274149.567
Shirdam, R., Shirka, A., Hassanoghli, S. and Bakhshi N. (2020). Investigating the effects of red mud and GGBFS industrial waste on the compressive strength of high-strength green concrete, Environmental Sciences, 17(4), 151-162. http://envs.sbu.ac.ir/article/view/26673
Shreekant, R.L., Mangalpady, A. and Harsha, V. (2016). Utilisation of mine waste in the construction industry - A Critical Review, International of Earth Science and Engineering, 9(1), 182-195.
Quality standards of Iranian soil resources and guidelines (2016). Office of Water and Soil, Deputy of Human Environment, Environmental Protection Organization.
Stevulova, N., Strigac, J., Junak, J., Terpakova, E. and Holub, M. (2021). Incorporation of Cement By pass Dust in Hydraulic Road Binder, Materials , 14, 41. https://dx.doi.org/10.3390/ma14010041
Tayebi-Khorami, M., Edraki, M., Corder, G. and Golev, A. (2019). Re-Thinking Mining Waste through an Integrative Approach Led by Circular Economy Aspirations, Minerals 2019, 9(5), 286, doi:10.3390/min9050286
Tran, M.V., Nguyen, C.V., Nawa, T. and Stitmannaithum, B. (2014). Properties of High Strength Concrete Using Steel Slag Coarse Aggregate, ASEAN Engineering Journal Part C, 4(2), 22-32.
U.S Environmental Protection Agency, (1993), MSW landfill criteria technical manual, subpart D. Environmental Protection Agency, Cincinnati.
U.S. Environmental Protection Agency (1989), Requirement for hazardous waste Landfill Design, Construction and Closure.
Vick, S.G. (1983). Planing, Design, and Analysis of Tailings Dams. (New York: John Wiley & Sons).
Volpe, R, (1979). Physical and Engineering Properties of Copper Tailings, Current Geotechnical Practice in Mine Waste Disposal, ASCE, 242 –260.
Williams, D.J., Wilson, G.W. and Panidis, C. (2003). Waste rock and tailings mixtures as a possible seal for potentially acid forming waste rock. (Paper presented at the 6th International Conference on Acid Rock Drainage, The Australasian Institute of Mining and Metallurgy, Melbourne). [Google Scholar]
Xu, H., Wei, C., Li, C., Fan, G., Deng, Z., Li, M. and Li, X. (2010). Sulfuric acid leaching of zinc silicate ore under pressure. Hydrometallurgy. 105 (1-2):186–190. https://doi.org/10.1016/j.hydromet.2010.07.014
Yilmaz, E., Belem, T., Benzaazoua, M. and Bussière, B. (2009). Experimental characterization of the influence of curing under stress on the hydromechanical and geochemical properties of cemented paste backf ill, (Paper presented at the Conference of Tailings and Mine Waste ’08, 2009, London.)
Zhang, S., Xue, X., Liu, X., Duan, P., Yang, H. and Jiang, T. (2006). Current situation and comprehensive utilization of iron ore tailing resources, J. Min. Sci. 42, 403–408. https://doi.org/10.1007/s10913-006-0069-9.
تعداد مشاهده مقاله: 475
تعداد دریافت فایل اصل مقاله: 762